Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway?()
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
您可能感興趣的試卷
你可能感興趣的試題
You work as a network technician at Company. Your boss, Mrs. , is interested in
GLBP. In particular, she wants to know the multicast address that this protocol uses.
What should you tell her? ()
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
A. IRDP
B. SNMP
C. HSRP
D. VRRP
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
In the hardware address 0000.0c07.ac0av,
what does 07.ac represent? ()
A. HSRP well-known physical MAC address
B. Vendor code
C. HSRP router number
D. HSRP group number
E. HSRP well-known virtual MAC address
A. per host using a round robin scheme
B. per host using a strict priority scheme
C. per session using a round robin scheme
D. per session using a strict priority scheme
E. per GLBP group using a round robin scheme
F. per GLBP group using a strict priority scheme
Which one of the statements below correctly describes the Virtual Router Redundancy Protocol (VRRP),
which is being used in the Company network to provide redundancy?()
A. A VRRP group has one active and one or more standby virtual routers.
B. A VRRP group has one master and one or more backup virtual routers.
C. A VRRP group has one master and one redundant virtual router.
D. None of the other alternatives apply
HSRP has been configured between two Company devices.
What kind of message does an HSRP configured router send out every 3 seconds?()
A. Retire
B. Coup
C. Resign
D. Send
E. Hello
To protect against first-hop router failure, four protocols were developed to ensure IP routing redundancy.
Which of the following are they?()
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in?()
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages?()
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
最新試題
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? ()
Which statement is correct about the use of the virtual interface on a WLC ?()
Which router redundancy protocol cannot be configured for interface tracking?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()