A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
您可能感興趣的試卷
你可能感興趣的試題
In the hardware address 0000.0c07.ac0av,
what does 07.ac represent? ()
A. HSRP well-known physical MAC address
B. Vendor code
C. HSRP router number
D. HSRP group number
E. HSRP well-known virtual MAC address
A. per host using a round robin scheme
B. per host using a strict priority scheme
C. per session using a round robin scheme
D. per session using a strict priority scheme
E. per GLBP group using a round robin scheme
F. per GLBP group using a strict priority scheme
Which one of the statements below correctly describes the Virtual Router Redundancy Protocol (VRRP),
which is being used in the Company network to provide redundancy?()
A. A VRRP group has one active and one or more standby virtual routers.
B. A VRRP group has one master and one or more backup virtual routers.
C. A VRRP group has one master and one redundant virtual router.
D. None of the other alternatives apply
HSRP has been configured between two Company devices.
What kind of message does an HSRP configured router send out every 3 seconds?()
A. Retire
B. Coup
C. Resign
D. Send
E. Hello
To protect against first-hop router failure, four protocols were developed to ensure IP routing redundancy.
Which of the following are they?()
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in?()
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages?()
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways?()
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP, VRRP, and GLBP?()
A. GLBP and VRRP allow for MD5 authentication, whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used, whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP, GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol (HSRP)? ()
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
最新試題
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Which two statements are true when the extended system ID feature is enabled? ()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. Which statement is true about the output?()
Refer to the exhibit. For what purpose is the command show ip cef used?()
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals?()
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()