To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
您可能感興趣的試卷
你可能感興趣的試題
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP， VRRP， and GLBP？（）
A. GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
You want to implement router redundancy in the Company network using the best method available.
Which protocol specified by RFC 2281 provides network redundancy for IP networks， ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits？（）
A. ICMP
B. IRDP
C. HSRP
D. STP
E. None of the other alternatives apply
pany uses GLBP to provide for router redundancy in the network.
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol （GLBP）？（）
A. Per host basis using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round-robin scheme
F. Per GLBP group using a round-robin scheme
HSRP has been configured between two Company devices.
Which of the following describe reasons for deploying HSRP？ （）
A. HSRP provides redundancy and fault tolerance
B. HSRP allows one router to automatically assume the function of the second router if the second router fails
C. HSRP allows one router to automatically assume the function of the second router if the second router starts
D. HSRP provides redundancy and load balancing
You want to implement a high availability network using two Cisco routers. You also want to ensure that the stat of the WAN interfaces can be tracked in doing so.
Which router redundancy protocol cannot be configured for interface tracking？ （）
A. GLBP
B. HSRP
C. RPR
D. VRRP
E. SLB
F. RPR+
G. None of the other alternatives apply
You need to configure two Company routers for high availability.
Which protocol enables a group of routers to form a single virtual router and use the real IP address of a router as the gateway address？ （）
A. HSRP
B. IRDP
C. Proxy ARP
D. GLBP
E. VRRP
F. None of the other alternatives apply
最新試題
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which two statements are true when the extended system ID feature is enabled？ （）