A. The glass core is doped with an Erbium in periodic segments of the fiber.
B. Layers of high index ?and low index ?material are deposited on a glass substrate.
C. Thin layers of silica glass are placed onto wafers to produce a prism-like effect.
D. Fiber is etched with an ultraviolet laser that is precisely spaced for specific wavelength filtering.
您可能感興趣的試卷
你可能感興趣的試題
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
A. offset the OADM loss at site B
B. overcome the high multiplexer loss at site A
C. amplify signal levels after the high loss through Fiber Span 1
D. adjust add channels at site B to be at the same level as the passthrough channels
E. ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ),
what does SNR IN represent?()
A. the signal to noise of the current optical amplifier
B. the signal to noise of the previous amplifier or source
C. the signal to noise introduced by the optical multiplexer
D. the accumulated noise to signal ratio of the optical channel
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm.
What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?()
A. none
B. -600 ps/nm
C. -200 ps/nm
D. +200 ps/nm
E. +600 ps/nm
A. 0.4 nanometers
B. 0.6 nanometers
C. 0.8 nanometers
D. 1.2 nanometers
E. 1.6 nanometers
Click the Exhibit button. Within an ONS 15454, you are provisioning a circuit on an unprotected SNCP ring. In the exhibit,
which two must you configure?()
A. revertive
B. circuit size
C. circuit type
D. bidirectional
E. protected drops
F. Switch on PDI-P
A. line timing
B. loop timing
C. internal timing
D. through timing
E. external timing
A. 512
B. 255
C. 1024
D. 4096
You are installing a Cisco ONS 15454 SDH in a service provider site. An E3 cable is being connected to a digital cross-connect system.
What is the maximum distance allowed between the two?()
A. 225 ft
B. 450 ft
C. 655 ft
D. 900 ft
A. An equal amount of working and protect bandwidth is required.
B. DCC bandwidth is not large enough to handle K1/K2 processing.
C. Switch times would exceed 50 ms for an STM-1 MS-SPRing ring.
D. There is not enough bandwidth in an STM-1 ring to justify MS-SPRing protection.
You are provisioning an E-1 circuit on an ONS 15454 SNCP configuration and XC-VXL-10G card.
How many total ports are used within the Low-Order matrix at the source node?()
A. 0
B. 1
C. 2
D. 3
E. 5
最新試題
On an ONS 15454 node you can tunnel a(n) ().
If node 2 is accepting line timing from node 1, node 2 will send () to node 1 as its SSM messge.
What are three relevant design considerations when using the 15216 EDFA?()
Which is a legitimate bandwidth matched pair?()
For lasers with tightly controlled wavelengths, approximately how far apart are the centers of adjacent wavelengths when 100 GHz spacing is used in a DWDM system? ()
SDH Code Violations (CVs) totals in the PM tables are actually an accumulation of the number of().
If the dispersion of a given fiber is 17ps/nm*km at 1550 nm and zero at 1310 nm, then what is the accumulated dispersion of an ITU wavelength after it travels 200 km? ()
Click the Exhibit button. Which type of multiplexer is shown in the exhibit?()
How is SNCP and MS-SPRing traffic rerouted during a protection switch when a complete fiber cable cut occurs?()
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?()