You are provisioning an E-1 circuit on an ONS 15454 SNCP configuration and XC-VXL-10G card.
How many total ports are used within the Low-Order matrix at the source node？（）
A. 0
B. 1
C. 2
D. 3
E. 5
您可能感興趣的試卷
你可能感興趣的試題
A. It protects signals against node failures between rings.
B. It protects signals against node failure within a single ring.
C. It allows for traffic to be preempted when a ring switch occurs.
D. Traffic can be dropped and continued at interconnecting nodes.
E. It protects preemptible traffic from being dropped when a ring switch occurs.
A customer would like to create a 1：1 protection group with a DS3Ni-12 card.
Where should it be placed in the chassis？（）
A. only Slots 6 or 12
B. only Slots 3 or 15
C. high or low speed slots
D. directly adjacent to the working card
E. high-speed slots only （5/6 and 12/13）
A customer has 20 E1s to add between far-end nodes in an SNCP ring.
What type of circuit would you recommend？（）
A. LO-PATH circuits
B. HO-PATH circuits
C. 1：1 protection circuits
D. 1：N protection circuits
E. LO-PATH tunnel circuits
Click the Exhibit button. As shown in the exhibit， a customer has several interconnected core rings. They want to create several irtual rings？utilizing their STM-64 backbone （nodes 1， 2， 3， and 4）.
What do you recommend？ （）
A. SNCP rings
B. MS-SPRing rings
C. 1：N protection on all core circuits
D. dual-ring interconnect with MS-SPRing rings
A customer has 2 E1s to add between far-end nodes in an SNCP ring.
What type of circuit should you recommend？ （）
A. LO-PATH circuits
B. HO-PATH circuits
C. 1：1 protection circuits
D. 1：N protection circuits
E. LO-TUNNEL tunnel circuits
A. signal fail， signal degrade， manual switch
B. signal degrade， signal fail， manual switch
C. protection lockout， manual switch， path AIS
D. forced switch， manual switch， signal degrade
E. protection lockout， manual switch， forced switch
A. LEX
B. HDLC
C. GFP-F
D. PPP/BCP
You are provisioning an E-1 circuit on an ONS 15454 MS-SPRing configuration and XC-VXL-10G card. Each VC-12 connection must also terminate via the VC-3 matrix.
How many VC-3 ports remain after this circuit is created， assuming no other circuits？（）
A. 92
B. 93
C. 94
D. 95
E. 96
A. 1+1 is based on APS， while 1：1 is based on IPS.
B. 1：1 is used in SNCP switching， while 1+1 is used in MS-SPRing switching.
C. 1+1 sends signals on Working and Protect paths， while 1：1 sends signals only on Working path.
D. 1+1 sends signals on Working path ONLY， while 1：1 sends signals on both Working and Protect paths.
A. 10
B. 32
C. 64
D. 84
E. 96
最新試題
What are two major differences between MS-SPRing and SNCP？（）
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux （left side） composite output and the ONS 15216 Demux （right side） composite input， with the optical values given in the exhibit？ （Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.） （）
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm. What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm？（）
Which timing mode is appropriate for an SDH NE that is adjacent to an SDH NE Bits-1 timing？ （）
A 2.5 Gb/s （OC-48 or STM-16） optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion. How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km？（）
Which two can be transported in one AU-4？ （）
What is the difference between the transmitted power and the sensitivity of the receiver？ （）
Why are the 1300 nm and 1550 nm regions of the fiber spectrum primarily used for optical communications？（）
What is the phenomenon called where different wavelengths of light travel at different speeds？（）
How is a Thin Film filter fabricated？ （）