On a Series 1010 lightweight access point， the alarm LED is flashing red， and all other LEDs are off.
What is the lightweight access point indicating？（）
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
您可能感興趣的試卷
你可能感興趣的試題
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
A.75
B.100
C.25
D.50
Client association using EAP-Cisco Wireless （LEAP） is failing， but EAP-PEAP is functioning on an autonomous access point.
Which of the following needs to be enabled on the access point so EAP-Cisco Wireless （LEAP） is enabled？（）
A.open authentication plus MAC
B.open authentication plus EAP
C.shared key
D.network EAP
A.Devices
B.IDS
C.Configure
D.Reports
A.1813
B.1645
C.1646
D.1812
A.chooses the least congested channel
B.uses the configured channel
C.sets all access points to the same channel
D.steps through each of the allowed channels
A.EAP-FAST master server
B.Allow automatic PAC provisioning
C.client initial message
D.authority ID info
最新試題
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）