You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.
In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
A.Take no action, you have achieved your goal.
B.Implement a Cisco Secure IPS sensor.
C.Implement a protected port on the access switches.
D.Implement 802.1X on the switch ports.
您可能感興趣的試卷
你可能感興趣的試題
A.Aggressive Load Balancing on
B.Aggressive Load Balancing off
C.Multicast on
D.Multicast off
E.AP Fallback on
F.AP Fallback off
A.MS-CHAP v2
B.PAP
C.GTC
D.MD5
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.
What can be done to correct the problem?()
A.Add 4GB RAM to the Cisco WCS.
B.Add a 120 GB hard drive to the Cisco WCS.
C.Add a new location appliance.
D.Add a new Cisco WCS server dedicated to the location appliance.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.
Which situation would result in thistype of problem?()
A.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication.
B.Clients have been set to validate the server identity.
C.Posture validation has not been enabled.
D.Clients and server are not using certificates.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.
What may cause this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol has been disabled
C.Publicly Secure Packet forwarding is enabled
D.The access point is set to the least congested channel.
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.
What does this indicate?()
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The internal radio has failed.
D.The access point is booting.
A.Your login does not have the correct permissions.
B.You must wait for the location server to become available.
C.Polling values can be changed only on the location server.
D.Polling values can be changed only in the maintenance window.
A.6 percent
B.12 percent
C.18 percent
D.24 percent
A.35
B.50
C.100
D.250
A.Wireless Control System
B.Wireless clients
C.Wireless controllers
D.Control-based access points
E.Location Appliance
最新試題
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications?()
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()