A.1813
B.1645
C.1646
D.1812
您可能感興趣的試卷
你可能感興趣的試題
A.chooses the least congested channel
B.uses the configured channel
C.sets all access points to the same channel
D.steps through each of the allowed channels
A.EAP-FAST master server
B.Allow automatic PAC provisioning
C.client initial message
D.authority ID info
A.A firmware upgrade is in progress.
B.The internal radio has failed.
C.An access point buffer overflow is occurring.
D.The access point is booting.
On a Cisco Aironet 1130 Series autonomous access point, the status indicator is blinking dark blue.
What does this indicate?()
A.The access point is booting.
B.A firmware upgrade is in progress.
C.The internal radio has failed.
D.An access point buffer overflow is occurring.
A.rogue detector
B.rogue containment
C.RLDP
D.RIDP
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The
phone rings but, when you answer, the call is dropped.
What may have caused this problem?()
A.Publicly Secure Packet forwarding is enabled.
B.The minimum data rate is not set to 11 Mbps.
C.An address resolution protocol is enabled.
D.The access point is set to the least congested channel.
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor, 4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the network and isbeing monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are beingtracked on the Cisco WCS.
What can be done to correct the problem?()
A.Add a new location appliance.
B.Add a new Cisco WCS server dedicated to the location appliance.
C.Add 4 GB of RAM to the Cisco WCS.
D.Add a 120 GB hard drive to the Cisco WCS.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kindof issue it is, you decide to increase the bandwidth reserved for roaming on the WLAN controllerto the maximum.
What level do you set the bandwidth to?()
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the WLSE, you are trying to push out a configuration job to a standalone access point, butthe job does not start.
Which of the following would cause this failure?()
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
A.50
B.128
C.512
D.1024
最新試題
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem?()