Using the WLSE, you are trying to push out a configuration job to a standalone access point, butthe job does not start.
Which of the following would cause this failure?()
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
您可能感興趣的試卷
你可能感興趣的試題
A.50
B.128
C.512
D.1024
You are using ADU and are authenticated and associated to an access point. However, you areunable to obtain an IP address.
Which of these has caused this problem?()
A.invalid SSID
B.invalid WEP key
C.invalid encryption type
D.invalid 802.1X authentication type
A.network connections
B.location views
C.access points
D.object definitions
You have been called upon to add location-based services into an existing controller-based
wireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.
In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However, when it is powered up, the access point fails.
What has caused this problem?()
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
On a standalone access point, client association using EAP-Cisco Wireless (Cisco-LEAP) is failing,but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue?()
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem?()
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
最新試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.What has causedthis problem?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()