A. Prepare, Plan, Create, Implement, Operate, and Improve
B. Prepare, Plan, Design, Implement, Operate, and Optimize
C. Prepare, Plan, Design, Apply, Operate, and Manage
D. Prepare, Plan, Design, Implement, Operate and Manage
您可能感興趣的試卷
你可能感興趣的試題
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 transport protocol
E. Layer 3 destination address
A.Prepare
B.Plan
C.Design
D.Operate
A. by snooping the CoS marking on the incoming frames
B. by using RTP hello messages between the switch port and the Cisco IP Phone
C. by using CDP
D. by using DHCP snooping
E. by snooping the incoming 802.1Q VLAN tag
A.IETF
B.PFC
C.ASIC
D.TCAM
A. Features such as UplinkFast and BackboneFast are compatible with RSTP.
B. An RSTP that is based on Cisco products generally performs better than the Cisco proprietary 802.1D enhancements.
C. Cisco proprietary enhancements are not transparent.
D. Information about port roles is sent to all switches.
E. RSTPs that are based on Cisco products require no additional configuration.
A. Implement threshold monitoring using RMON.
B. Implement monitoring using SNMP or RMON.
C. Poll and record specific SNMP MIB objects from the device.
D. Verify that SNMP MIB is supported in the relevant core device.
A. TCP-based hello packets
B. the impact of flapping links if timers are too low
C. a shared single interface
D. the ability to track serial interfaces
E. UDP-based hello packets
A. Cisco is focusing on Cisco Validated Designs as a means to driving integrated networks.
B. Cisco is focusing on the PIN architecture as a means to driving integrated networks.
C. The Cisco PIN architecture is a critical mechanism for supporting integrated markets because it can be implemented quickly.
D. The Cisco Validated Designs program provides critical mechanisms for supporting integrated markets because the mechanisms can be implemented quickly.
E. Cisco Validated Designs can be implemented quickly without customer input.
A. start LDP
B. enable CEF switching
C. configure the MPLS ID
D. disable IP TTL propagation
E. configure conditional label advertising
F. enable label switching on frame mode interfaces
A. show status
B. show hardware
C. show inventory
D. show environment
最新試題
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?()
On the Catalyst 6500 Series switch, which command is used to establish a console connection to the Firewall Services Module?()
Refer to the exhibit. Which two of these statements are correct? (Choose two.)()
With a VPN Accelerator Module 2+ (VAM2+) installed in a Cisco 7200 series router, what will be the resulting action when entering the command no crypto engine accelerator slot number?()
In a high-availability network, which command, when placed on ports that have connected end stations, will allow you to prevent delays in service for end stations by placing a port in blocking mode?()
What are four advantages to using tunnel brokers in an IPv6 transition environment?()
You are an experienced network administrator in an international corporation. During your working hours, you are asked to deploy the Cisco SSL VPN AIM module in a Cisco 1800 Series Router. The beneficial reason for that deployment is to:()
What is the purpose of using VPN hardware acceleration equipment?()
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?()
You are trying to initiate an SSH connection to a remote router and are getting rejected with an error code of 0. Which of these might be the cause of the error?()