Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
您可能感興趣的試卷
你可能感興趣的試題
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
A.10.188.31.0/27
B.10.188.31.0/26
C.10.188.31.0/29
D.10.188.31.0/28
E.10.188.31.0/25
Refer to the exhibit.A network technician is asked to design a small network with redundancy. The exhibit represents this design， with all hosts configured in the same VLAN. What conclusions can be made about this design？（）
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2.
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
Refer to the exhibit.After a RIP route is marked invalid on Router_1， how much time will elapse before that route is removed from the routing table？（）
A.30 seconds
B.60 seconds
C.90 seconds
D.180 seconds
E.240 seconds
A.proxy
B.dual-stack
C.tunneling
D.dot1q
A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration， a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However， pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem？（）
A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.
最新試題
請參見圖示。對于從主機A 向Web 服務器發出的網頁請求，正確的目的套接字數字是什么？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
路由器使用哪一項信息來確定源主機和目的主機之間的路徑？（）
請參見圖示。已啟用路由器的NAT 功能供PC 訪問Internet?？梢詾槁酚善鹘涌赟0/0/0分配下列哪一個IP 地址？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
下列哪些是私有IP 地址的地址范圍？（）
以下哪兩種介質可提供高達1Gb/s 的帶寬？（）
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）
要將數據包發送到遠程網絡，應使用哪種設備？（）