多項選擇題

An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
 

A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50


您可能感興趣的試卷

你可能感興趣的試題

2.單項選擇題

Refer to the exhibit.A network technician is asked to design a small network with redundancy. The exhibit represents this design， with all hosts configured in the same VLAN. What conclusions can be made about this design？（）

A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.

3.單項選擇題Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?（）

A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2.

4.多項選擇題Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?（）

A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan

7.單項選擇題The enable secret command is used to secure access to which CLI mode?（）

A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode

8.多項選擇題Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

9.單項選擇題

Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration， a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However， pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem？（）

A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.

10.單項選擇題Which statement about vlan operation on cisco catalyst switches is true?（）

A.when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table
B.unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C.ports between switches should be configured in access mode so that vlans can span across the ports
D.broadcast and multicast frames are retransmitted to ports that are configured on different vlan.

最新試題

請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）

題型：單項選擇題

請參見圖示。哪種邏輯拓撲是對圖示網絡的準確描述？（）

題型：單項選擇題

請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置？（）

題型：單項選擇題

請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序？（）

題型：單項選擇題

請參見圖示。對于從主機A 向Web 服務器發出的網頁請求，正確的目的套接字數字是什么？（）

題型：單項選擇題

請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）

題型：單項選擇題

在Cisco IOS 設備中，啟動配置文件存儲于何處？（）

題型：單項選擇題

請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論？（）

題型：多項選擇題

在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）

題型：單項選擇題

OSI 模型的哪兩項功能在第2層實現？（）

題型：多項選擇題