A.Frame Monitoring
B.Radio Scan
C.Self-Healing
D.Client Walkabout
您可能感興趣的試卷
你可能感興趣的試題
You are trying to deploy a configuration job to an IOS access point using the WLSE, but the jobfails.
Which of the following would cause this failure?()
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
A.3
B.1
C.4
D.6
A.PSK authentication
B.EAP authentication
C.WPA authentication
D.Web authentication
VLANs have been enabled on an autonomous access point.
In order for clients associating toVLANs other than the native VLAN to receive an IP address which of the following must beconfigured?()
A.access point Ethernet port set to SSL trunking
B.switchport set to 802.1q trunking
C.switchport set to SSL trunking
D.access point Ethernet port not set to 802.1q trunking
A.router(config)# wlccp authentication-server infrastructure eap Group_1
B.router(config)# wlccp authentication-server infrastructure eap-fast Group_1
C.router(config)# wlccp authentication-server client eap-fast Group_1
D.router(config)# wlccp authentication-server client eap Group_1
A.registration error
B.authentication failures threshold
C.HTTP disabled
D.Telnet disabled
A.802.1q trunking
B.VTP trunking
C.ISL trunking
D.DPT trunking
There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab, you notice a red indicator on the WDS access point.Upon inspection of the WDS access point through its GUI, it is discovered that the security keys arenot set up between the WDS access point and the WLSE.
Which of the following is misconfigured?()
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
You are using ADU and are authenticated and associated to an access point. You are unable toobtain an IP address.
Which of the following will cause this problem?()
A.AES encryption enabled
B.TKIP enabled
C.third-party wireless supplicant enabled
D.802.1X authentication type enabled
On a Series 1010 lightweight access point, the alarm LED is flashing red, and all other LEDs are off.
What is the lightweight access point indicating?()
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
最新試題
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()