You are using standalone cisco aironet 1400 series wireless bridges for a nine-mile point-to-point wireless link between two buildings.
Which distance setting should you use for the bridge configured as the root？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
您可能感興趣的試卷
你可能感興趣的試題
When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct？（）
A.router（config-if）# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router（config-if）# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router（config-if）# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router（config-if）# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
Eap-fast provides a secure tunnel during phase one to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.pre shared key
D.protected access credential
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however，employees there have been experiencing problems when tracking objects using active rfid tags. the rfid beacon rate is 10 seconds and you have discovered an issue with the rfid timeout value.
Where and how should the rfid value be changed？（）
A.on the cisco wcs， to 95 seconds
B.on the wireless controller， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the cisco wcs， to 45 seconds
You are installing a cisco aironet 1000 series controller-based access point. when you boot it， all the leds on the access point blink together.
What does this indicate about the access point？（）
A.duplicate ip address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.ipx
B.ip
C.udp
D.tcp
A.14
B.15
C.17
D.16
A.location appliance
B.controller-based access points
C.wireless clients
D.wireless control system
E.wireless controllers
A.48
B.36
C.12
D.24
A.10
B.5
C.15
D.20
最新試題
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）