A.10
B.5
C.15
D.20
您可能感興趣的試卷
你可能感興趣的試題
A.project planning
B.configuration management
C.wireless readiness assessment
D.systems acceptance testing
E.site readiness specification
A.4 to 6 times the tag beaconing rate
B.10 to 12 times the tab beaconing rate
C.8 to 10 times the tag beaconing rate
D.6 to 8 times the tag beaconing rate
A.mirror
B.rogue detector
C.sniffer
D.monitor
A client roams from h-reap ap1 to h-reap ap2. the client is unable to associate to h-reap ap2. h-reap ap2 has six other clients associated to it, which continue to pass traffic.
What has caused this problem?()
A.h-reap ap1 has reached its client limit.
B.h-reap ap2 has reached its client limit.
C.h-reap ap2 lost its connection to the controller.
D.h-reap ap1 lost its connection to the controller.
You are trying to change the polling parameters used by the location manager via the cisco wcs, and your request is being denied.
What is wrong?()
A.polling values can be changed only in the maintenance window.
B.polling values can be changed only on the location server.
C.your login does not have the correct permissions.
D.you must wait for the location server to become available.
A.system monitoring
B.security administration
C.operations setup
D.problem management
On a cisco 1000 series controller-based access point,the alarm led is flashing red,but the other leds are off.
What is this access point indicating?()
A.its ip address already exists.
B.it is operating normally.
C.it requires a code upgrade.
D.it has lost contact with the controller.
A.admin
B.users assistant
C.system monitoring
D.power users
E.administrators
F.network operator
Clients using cisco-leap and eap-fast authentication are having no problems logging on to The wireless network, but clients using peap are failing to log on.
Which situation would result in this type of problem?()
A.posture validation has not been enabled.
B.the aaa server is set to accept both ms-chap v2 and gtc for peap authentication.
C.clients and server are not using certificates.
D.clients have been set to validate the server identity.
A.3
B.6
C.4
D.1
最新試題
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()