The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/
1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
您可能感興趣的試卷
你可能感興趣的試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）
ipv6 router ospf 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000 ::1/64
ipv6 ospf 1 area 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 ospf 1 area 0
A. OSPF works on F0/0 and S0/0/0 without further configuration
B. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
C. OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
D. OSPFv3 needs at least two more configuration commands before it works on R1
A. The method of choosing an OSPF router ID
B. Verification checks that must be validated before two routers can become OSPF neighbors
C. Support for route tags
D. Support for multiple instances per inter face
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）
interface f0/0
mac - address 1111.1111.1 111
ipv6 address 2000::/64 eui - 64
ipv6 address 2001::1/64
A. The next hop is 2000::1311:11FF:FE11:1111
B. The next hop is FE80::1311:11FF:FE11:1111
C. The next hop is FE80::5111:11FF:FE11:1111
D. The next hop is 2001::1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）
ipv6 router eigrp 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000::1/64
ipv6 eigrp 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 eigrp 1
A. EIGRP works on F0/0 and S0/0/0 without further configuration
B. EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
C. EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
D. EIGRP for IPv6 needs at least two more configuration commands before it works on R1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）
ipv6 unicast- routing
interface f0/0
ipv6 rip one enable
ipv6 address 2000::1/64
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 rip one enable
A. RIPng will be enabled on no interfaces.
B. RIPng will be enabled on one interface.
C. RIPng will be enabled on two interfaces.
D. RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.
A. Distance Vector Logi c
B. Uses UDP
C. Uses RIP - specific authentication
D. Maximum useful metric of 15
E. Automatic route summarization
Router R1 lists the following output from a show command. Which of the following is true about R1?（）
R1# show ip v6 interface f0/0
FastEthernet0/0 is up, line protocol is up
IPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456
No Virtual link - local address(es):
Global unicast address(es):
2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]
Jo ined group address(es):
FF02::1
FF02::2
FF02::1:FF:12:3456
A. R1's solicited node multicast address is FF02::1:FF:12:3456.
B. R1's 2000::4:213:19FF:FE12:3456 address is a global unicast with all 128 bits statically configured.
C. Address FF02::2 is R1's solicited node multicast.
D. R1's solicited node multicast, not listed in this output, would be FF02::213:19FF:FE12:3456.
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）
interface f0/0
ipv6 address 2345:0:0:8::1/64
A. 2345:0:0:8::1
B. 2345:0:0:8:0:FF:FE11:1111
C. FE80::8:0:FF:FE11:1111
D. FE80:0:0:8::1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.
Which of the following could be the link local address of R1's interface S0/0?（）
A. FEA0::200:FF:FE11:0
B. FE80::200:FF:FE11:1111
C. FE80::0213:19FF:FE7B:0:1
D. FEB0::211:11FF:FE11: 1111
A. 2000::1:1234:5678:9ABC
B. FD80::1:1234:5678:9ABC
C. FE80::1:1234:5678:9ABC
D. FF80::1:1234:5678:9ABC
最新試題
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）