A.Changing the bridge priority of S1 to 4096 would improve network performance.
B.Changing the bridge priority of S1 to 36864 would improve network performance.
C.Changing the bridge priority of S2 to 36864 would improve network performance.
D.Changing the bridge priority of S3 to 4096 would improve network performance.
E.Disabling the Spanning Tree Protocol would improve network performance.
F.Upgrading the link between S2 and S3 to Gigabit Ethernet would improve performance.

A.The BID is made up of the bridge priority value（two bytes） and bridge MAC address （six bytes）.
B.The BID is made up of the bridge priority （four bits）， the system ID （12 bits）， and a bridge MAC address （48 bits）.
C.The BID is made up of the system ID （six bytes） and bridge priority value （two bytes）.
D.The system ID value is the VLAN ID （VID）.
E.The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F.The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.

A.BPDUs will be sent out every two seconds.
B.The time spent in the listening state will be 30 seconds.
C.The time spent in the learning state will be 15 seconds.
D.The maximum length of time that the BPDU information will be saved is 30 seconds.
E.This switch is the root bridge for VLAN 200.
F.BPDUs will be sent out every 10 seconds.

A.HSRP
B.GLBP
C.VRRP
D.SLB
E.RPR
F.RPR+

A.STP timers values （hello， forward delay， max age） are included in each BPDU.
B.A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
C.To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.
D.If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.
E.On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.
F.The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.

A.DSW11（config）# spanning-tree vlan 1 priority 4096
B.DSW12（config）# set spanning-tree priority 4096
C.ASW13（config）# spanning-tree vlan 1 priority 4096
D.DSW11（config）# set spanning-tree priority 4096
E.DSW12（config）# spanning-tree vlan 1 priority 4096
F.ASW13（config）# set spanning-tree priority 4096

A.DSW11 will be elected the root bridge.
B.DSW12 will be elected the root bridge.
C.ASW13 will be elected the root bridge.
D.P3/1 will be elected the nondesignated port.
E.P2/2 will be elected the nondesignated port.
F.P3/2 will be elected the nondesignated port.

A.Upon bootup，a port transitions from blocking to forwarding because it assumes itself as root.
B.Upon bootup，a port transitions from blocking to listening because it assumes itself as root.
C.Upon bootup，a port transitions from listening to forwarding because it assumes itself as root.
D.If a forwarding port receives no BPDUs by the max_age time limit， it will transition to listening.
E.If a forwarding port receives an inferior BPDU， it will transition to listening.
F.If a blocked port receives no BPDUs by the max_age time limit， it will transition to listening.

A.TEST1 is configured as a VTP server with a different domain name.
B.TEST1 is not configured to participate in VTP.
C.TEST1 is configured as a VTP server with the domain name main1.
D.TEST1 has a lower VTP configuration revision than the current VTP revision.
E.TEST1 has a higher VTP configuration revision than the current VTP revision.
F.TEST1 is configured with only VLAN1.