Each of these vlans has one host each on its port SVI on vlan 1 - ip 192.168.1.11 with snm Switch B -
Ports 3， 4 connected to ports 3 and 4 on Switch A
Port 15 connected to Port on Router.
Tasks to do
1. Use non proprietary mode of aggregation with Switch B being the initiator -- Assumed use LACP with B being in Active mode
2. Use non proprietary trunking and no negotiation -- Assumed use switchport mode trunk and switchport trunk encapsulation dot1q
3. Restrict only to vlans needed
-- Assumed either vtp pruning or allowed vlan list. vtp pruning command did not seem to work on the simulator so landed using allowed vlan list
4. SVI on vlan 1 with some ip and subnet given
5. Configure switch A so that nodes other side of Router C are accessible -- Assumed this to mean that on switch A default gatway has to be configured.
6. Make switch B the root
-- Could not get this to work. Exam hung when I tried the command spanning-tree vlan 1，21-23 priority 4096
您可能感興趣的試卷
你可能感興趣的試題
Configure the Multilayer Switch so that PCs from VLAN 2 and VLAN 3 can communicate with the Server.
A.TCP retransmits
B.benign
C.greedy
D.drop sensitive
E.smooth
F.delay insensitive
Refer to the exhibit. The command spanning-tree guard root is configured on interface Gi0/0 on both switch S2 and S5. The global configuration command spanning-tree uplinkfast has been configured on both switch S2 and S5. The link between switch S4 and S5 fails.
Will Host A be able to reach Host B？ （）
A.Yes. Traffic can pass either from switch S6 to S3 to S2 to S1， or， from switch S6 to S5 to S2 to S1.
B.No. Traffic will pass from switch S6 to S5 and dead-end at interface Gi 0/0.
C.No. Traffic will loop back and forth between switch S5 and S2.
D.Yes. Traffic will pass from switch S6 to S3 to S2 to S1.
E.No. Traffic will either pass from switch S6 to S5 and dead-end， or traffic will pass from switch S6 to S3 to S2 and dead-end.
On an Aironet card， LED 0 and LED 1 are blinking alternately.
What does this indicate？ （）
A.The Aironet card is in power save mode.
B.The Aironet card is looking for a network association.
C.The Aironet card is joined to a network， but there is no network activity.
D.The Aironet card is joined to a network， and there is network activity.
A.Static secure MAC addresses can be configured in conjunction with voice VLANs.
B.PortFast is automatically enabled when voice VLANs are configured.
C.PortFast must be manually configured when voice VLANs are configured.
D.Voice VLANs are typically configured on uplink ports.
E.Voice VLANs are typically configured on access ports.
Refer to the exhibit.
Which statement is true about the display of the command show pagp 1 neighbor command？（）
A.STP packets are sent out the Gi0/1 interface only.
B.STP packets are sent out both the Gi0/1 and Gi0/2 interfaces.
C.CDP packets are sent out the Gi0/1 interface only.
D.CDP packets are sent out the Gi0/2 interface only.
A.allows an UDLD port to automatically reset when it has been shutdown
B.resets all UDLD enabled ports that have been shutdown
C.removes all UDLD configurations from interfaces that were globally enabled
D.removes all UDLD configurations from interfaces that were enabled per-port
Refer to the exhibit. When a profile is configured in the Aironet Desktop Utility，
which security option permits the configuration of host-based Extensible Authentication Protocol （EAP）？（）
A.WPA/WPA2/CCKM
B.WPA/WPA2 Passphrase
C.802.1x
D.Pre-Shared Key （Static WEP）
Network topology exhibit：
Interface VLAN 101 exhibit：
Interface VLAN 102 exhibit：
Interface VLAN 104 exhibit：
Interface VLAN 105 exhibit：
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches 1 and 2. 1 is the primary device for Vlan 101， 102， 105. 2 is the primary device for Vlan 103 and 104
Note： Please refer to the #2 scenario.
During routine maintenance， it became necessary to shutdown G1/0/1 on1 and2.
All other interface were up. During this time，1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group.
What can be done to make the group function properly ？（）
A.On 1， disable preempt
B.On 2， decrease the priority value to a value less than 150
C.On 1， increase the decrement value in the track command to a value greater than 6
D.On 1， disable track command.
Network topology exhibit：
Interface VLAN 101 exhibit：
Interface VLAN 102 exhibit：
Interface VLAN 104 exhibit：
Interface VLAN 105 exhibit：
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches1 and 2. 1 is the primary device for Vlan 101， 102， 105. 2 is the primary device for Vlan 103 and 104
Note： Please refer to the #2 scenario.
2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group.
What can be done to make the group function properly ？（）
A.On 1， disable preempt
B.On 1， decrease the priority value to a value less than 190 and greater than 150
C.On 2， increase the priority value to a value greater 241 and less than 249
D.On 2， increase the decrement value in the track command to a value greater than 10 and less than 50.
最新試題
Which three statements about STP timers are true？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）