Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
您可能感興趣的試卷
你可能感興趣的試題
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Refer to the exhibit. The web servers WS_1 and WS_2 need to be accessed by external and internal users. For security reasons， the servers should not communicate with each other，
although they are located on the same subnet. The servers do need， however， to communicate with a database server located in the inside network.
What configuration will isolate the servers from each other？ （）
A. The switch ports 3/1 and 3/2 will be defined as secondary VLAN community ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
B. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
C. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN community ports.
D. The switch ports 3/1 and 3/2 will be defined as secondary VLAN isolated ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
pany is implementing 802.1X in order to increase network security. In the use of 802.1X
access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. EAP-over-LAN
B. EAP MD5
C. STP
D. protocols not filtered by an ACL
E. CDP
F. TACACS+
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
The Company security administrator wants to prevent DHCP spoofing.
Which statement is true about DHCP spoofing operation？（）
A. DHCP spoofing and SPAN cannot be used on the same port of a switch.
B. To prevent a DHCP spoofing， the DHCP server must create a static ARP entry that cannot be updated by a dynamic ARP packet.
C. To prevent a DHCP spoofing， the switch must have DHCP server services disabled and a static entry pointing towards the DHCP server.
D. DHCP spoofing can be prevented by placing all unused ports in an unused VLAN.
E. None of the other alternatives apply.
The Company security administrator is concerned with layer 2 network attacks.
Which two statements about these attacks are true？ （）
A. ARP spoofing attacks are attempts to redirect traffic to an attacking host by encapsulating a false 802.1Q header on a frame and causing traffic to be delivered to the wrong VLAN.
B. ARP spoofing attacks are attempts to redirect traffic to an attacking host by sending an ARP message with a forged identity to a transmitting host.
C. MAC address flooding is an attempt to force a switch to send all information out every port byoverloading the MAC address table.
D. ARP spoofing attacks are attempts to redirect traffic to an attacking host by sending an ARP packet that contains the forged address of the next hop router.
E. MAC address flooding is an attempt to redirect traffic to a single port by associating that port with all MAC addresses in the VLAN.
You work as a network technician at Company. Your boss, Mrs. , is interested in
switch spoofing.
She asks you how an attacker would collect information with VLAN hoping through switch spoofing. You should tell her that the attacking station... （）
A、...uses VTP to collect VLAN information that is sent out and then tags itself with the domain information in order to capture the data.
B、...will generate frames with two 802.1Q headers to cause the switch to forward the frames to a VLAN that would be inaccessible to the attacker through legitimate means.
C、...uses DTP to negotiate trunking with a switch port and captures all traffic that is allowed on the trunk.
D、...tags itself with all usable VLANs to capture data that is passed through the switch， regardless of the VLAN to which the data belongs.
E、None of the other alternatives apply
You are responsible for increasing the security within the Company LAN. Of the following choices listed below，
which is true regarding layer 2 security and mitigation techniques？ （）
A. Enable root guard to mitigate ARP address spoofing attacks.
B. Configure DHCP spoofing to mitigate ARP address spoofing attacks.
C. Configure PVLANs to mitigate MAC address flooding attacks.
D. Enable root guard to mitigate DHCP spoofing attacks.
E. Configure dynamic APR inspection （DAI） to mitigate IP address spoofing on DHCP untrusted ports.
F. Configure port security to mitigate MAC address flooding
G. None of the other alternatives apply
Refer to the exhibit. An attacker is connected to interface Fa0/11 on switch A-SW2 and attempts to establish a DHCP server for a man-in-middle attack.
Which recommendation， if followed， would mitigate this type of attack？（）
A. All switch ports in the Building Access block should be configured as DHCP untrusted ports.
B. All switch ports in the Building Access block should be configured as DHCP trusted ports.
C. All switch ports connecting to servers in the Server Farm block should be configured as DHCP untrusted ports.
D. All switch ports connecting to hosts in the Building Access block should be configured as DHCP trusted ports.
E. All switch ports in the Server Farm block should be configured as DHCP untrusted ports.
F. All switch ports connecting to hosts in the Building Access block should be configured as DHCP untrusted ports.
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. Which statement is true about the output？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）