單項選擇題Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?（）

A.BackboneFast
B.UplinkFast
C.Root Guard
D.BPDU Guard
E.BPDU Filter


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

A.The process id is configured improperly
B.The OSPF area is configured improperly
C.The network wildcard mask is configured improperly
D.The network number is configured improperly
E.The AS is configured improperly
F.The network subnet mask is configuerd improperly

2.單項選擇題

Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network.The network administrator connected to console port,issued the show ip route command,and was able to ping the server.Based on the output of the show ip route command topology shown in the graphic,what is the cause of the failure?（）

A.IP routing is not enabled
B.A static route is configured incorrectly
C.The network has not fully converged
D.The FastEthernet interface on Coffee is disabled
E.The routing table on Coffee has not updated
F.The neighbor relationship table is not correctly updated

3.單項選擇題A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How can you accomplish this task,using the fewest physical interfaces and without decreasing network performance?（）

A.Add two more FastEthernet interfaces.
B.Add a second router to handle the vlan traffic.
C.Use a hub to connect the four vlans with a FastEthernet interface on router.
D.Implement a router-on-a-stick configuration.

4.單項選擇題

Refer to the exhibit a network administrator cannot establish a telnet session with the indicated router at is the cause of this failure?（）

A .A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access

5.單項選擇題Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

A.As numbers must be changed to match on all the routers.
B.Loopback interface must be configured so a DR is elected.
C.The no auto-summary command is needed on Router A and Router C.
D.Router B needs to have two network statements, one for each connected network.

6.單項選擇題

Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?（）

A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.
B.Remote access management of this switch will not be possible without configuration change.
C.More VLANs will need to be created for this switch.
D.The switch will need a different IOS code in order to support VLANs and STP.

7.單項選擇題Select the action that results from executing these commands.（）Switch(config-if)# switchport port-securitySwitch(config-if)# switchport port-security mac-address sticky

A.A dynamically learned MAC address is saved in the startup-configuration file.
B.A dynamically learned MAC address is saved in the running-configuration file.
C.A dynamically learned MAC address is saved in the VLAN database.
D.Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E.Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

8.多項選擇題Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch?（）

A.SW1#show swithport port-security interface FastEthernet 0/12
B.SW1# show swithport port-secure interface FastEthernet 0/12
C.SW1# show port-secure interface FastEthernet 0/12
D.SW1#show running-config
E.SW1#show port-security interface FastEthernet 0/12

9.多項選擇題Which can be done to secure the virtual terminal interfaces on a router?（）

A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and apply it to the terminal interfaces using the access-class command.
E.Create an access list and apply it to the terminal interfaces using the access-group command.

10.多項選擇題A network administrator is configuring ACLs on a cisco router, to allow affic from hosts on networks 192.168.146.0,192.168.147.0,192.168.148.0 and 192.168.149.0 only.Which two ACL statements when combined are the best for accomplishing the task?（）

A.access-list 10 permit ip 192.168.147.0 0.0.0.255.255
B.access-list 10 permit ip 192.168.149.0 0.0.0.255.255
C.access-list 10 permit ip 192.168.146.0 0.0.0.0.255
D.access-list 10 permit ip 192.168.146.0 0.0.1.255
E.access-list 10 permit ip 192.168.148.0 0.0.1.255
F.access-list 10 permit ip 192.168.146.0 255.255.255.0