A.As numbers must be changed to match on all the routers.
B.Loopback interface must be configured so a DR is elected.
C.The no auto-summary command is needed on Router A and Router C.
D.Router B needs to have two network statements, one for each connected network.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?（）
A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.
B.Remote access management of this switch will not be possible without configuration change.
C.More VLANs will need to be created for this switch.
D.The switch will need a different IOS code in order to support VLANs and STP.
A.A dynamically learned MAC address is saved in the startup-configuration file.
B.A dynamically learned MAC address is saved in the running-configuration file.
C.A dynamically learned MAC address is saved in the VLAN database.
D.Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E.Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.
A.SW1#show swithport port-security interface FastEthernet 0/12
B.SW1# show swithport port-secure interface FastEthernet 0/12
C.SW1# show port-secure interface FastEthernet 0/12
D.SW1#show running-config
E.SW1#show port-security interface FastEthernet 0/12
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and apply it to the terminal interfaces using the access-class command.
E.Create an access list and apply it to the terminal interfaces using the access-group command.
A.access-list 10 permit ip 192.168.147.0 0.0.0.255.255
B.access-list 10 permit ip 192.168.149.0 0.0.0.255.255
C.access-list 10 permit ip 192.168.146.0 0.0.0.0.255
D.access-list 10 permit ip 192.168.146.0 0.0.1.255
E.access-list 10 permit ip 192.168.148.0 0.0.1.255
F.access-list 10 permit ip 192.168.146.0 255.255.255.0
A.access-list 50 deny 192.168.1.1 0.0.0.255
B.access-list 110 permit ip any any
C.access-list 2500 deny tcp any host 192.168.1.1 eq 22
D.access-list 101 deny tcp any host 192.168.1.1
A.you can apply multiple access lists with the same protocol or in different direction.
B.you can config one access list,per direction,per layer 3 protocol
C.you can place as many access lists as you want on any interface
D.you can apply only one access list on any interface
A.They are always present in the NAT table.
B.They allow connection to be initiated from the outside.
C.They can be configured with access lists, to allow two or more connections to be initiated from the outside.
D.They require no inside or outside interface markings because addresses are statically defined.
A.network or subnetwork IP address
B.broadcast address on the network
C.IP address leased to the LAN
D.IP address used by the interfaces
E.manually assigned address to the clients
F.designated IP address to the DHCP server
A.Set the IP gateway to be used by the network.
B.Perform host discovery used DHCPDISCOVER message.
C.Configure IP address parameters from DHCP server to a host.
D.Provide an easy management of layer 3 devices.
E.Monitor IP performance using the DHCP server.
F.Assign and renew IP address from the default pool.
最新試題
Which three statements about Syslog utilization are true?（）
What Netflow component can be applied to an interface to track IPv4 traffic?（）
In a GLBP network, who is responsible for the arp request?（）
What parameter can be different on ports within an EtherChannel?（）
Which three features are added in SNMPv3 over SNMPv2 ? （）
Which three statements about HSRP operation are true?（）
What SNMP message alerts the manager to a condition on the network?（）
Which statement describes the process ID that is used to run OSPF on a router ?（）
What are the Popular destinations for syslog messages to be saved? （）
What OSPF command, when configured, will include all interfaces into area 0?（）