A.The OSPF area is not configured properly.
B.The priority on R1 should be set higher.
C.The cost on R1 should be set higher.
D.The hello and dead timers are not configured properly.
E.A backup designated router needs to be added to the network.
F.The OSPF process ID numbers must match.
您可能感興趣的試卷
你可能感興趣的試題
A.data link
B.network
C.physical
D.transport
A.A remote physical layer problem exists.
B.The host NIC is not functioning.
C.TCP/IP has not been correctly installed on the host.
D.A local physical layer problem exists.
A. 10.15.32.17
B. 17.15.66.128
C. 66.55.128.1
D. 135.1.64.34
E. 129.33.192.192
F. 192.168.5.63
A.telnet access does not require a password
B.nat
C.no broadcast
D.chanage of destination address in the ipv6 header
E.chanage of source address in the ipv6 header
F.autoconfiguration
A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.
A.show frame-relay map
B.show frame-relay lmi
C.show inter serial
D.show frame-relay pvc
A.24
B.4
C.3
D.16
A.B514:82C3:0029::EC7A:0000:EC72
B.B514:82C3:0029:EC7A:EC72
C.B514:82C3::0029:EC7A:0:EC72
D.B514:82C3::0029:EC7A:EC72
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()
A.The Gallant router has the wrong LMI type configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the subinterface B
B.Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
最新試題
請參見圖示。公司路由器由于故障被更換。更換路由器之后,Education 辦公室內的主機C 和D 能夠相互ping 通,但是無法訪問Accounts 辦公室內的主機。此問題的原因可能是什么?()
路由器使用哪一項信息來確定源主機和目的主機之間的路徑?()
在Cisco IOS 設備中,啟動配置文件存儲于何處?()
何時必須使用clock rate 命令配置路由器串行接口?()
請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么?()
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲写嬖诙嗌賯€(gè)廣播域?()
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時,它的目的MAC 地址是什么?()
PC 無法連接到任何遠程網站,無法ping 通其默認網關,也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常?()
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置?()