A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing,you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.
How many interior walls can you add to improve the accuracy of thelocation appliance?()
A.50
B.100
C.150
D.200
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.
What may cause this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
A.45
B.60
C.15
D.30
A.client traffic allowed, data captured on all channels
B.client traffic allowed, data captured on a single channel
C.no client traffic allowed, data captured on a single channel
D.no client traffic allowed, data captured on all channels
You are installing a Cisco 4402 Series Wireless LAN Controller.
What type of interface is used on the uplink port?()
A.1000Base-X Mini-GBIC
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.1000Base-SX
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.
Which of the following will cause this problem?()
A.invalid radio type selected
B.no WEP key configured on the client
C.invalid SSID configured
D.invalid WEP key
A.Object Definitions
B.Asset Management
C.Location Views
D.Network Connections
An REAP was supporting 16 WLANs, but now it only supports one.
What happened to cause the change?()
A.Controller connectivity has been lost.
B.The access point lost its configuration.
C.The access point was rebooted.
D.An access point firmware upgrade is in progress.
A rogue access point is detected on the Cisco WCS console. Upon investigation, the access point isdiscovered to belong to a neighboring business.
Your administrator should designate the rogueaccess point as which of the following?()
A.known internal
B.managed
C.friendly
D.known external
A.30 mW
B.100 mW
C.40 mW
D.50 mW
A.RTS
B.distance(kilometers)
C.concatenation
D.CCA
最新試題
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.What has causedthis problem?()
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()