Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）
A. Add the area 1 stub command on routers R1.
B. Add the always keyword to the default - information originate configuration command on router R2.
C. Remov e the default information originate configuration command from router R2 and place it on router R1.
D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
您可能感興趣的試卷
你可能感興趣的試題
A. The BGP split - horizon rule specifies that routes learned via EBGP are never propagated to other IBGP peers.
B. The BGP split horizon rule specifies that routes learned via IBGP are never propagated to other IBGP peers.
C. A full - mesh IBGP requires that neighbor relationships be established between a ll BGP enabled routers in the autonomous system.
D. IBGP neighbors must be in different autonomous systems.
E. An EGP or static routing is required between IBGP neighbors.
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）
A. the routes originating from the RIP routing domain
B. the routes originating from the OSPF stub area
C. all OSPF inter and intra - area routes
D. all routes originating from RIP and OSPF routing domains
Refer to the exhibit. Will redistribute d RIP routes from OSPF Area 2 be allowed in Area 1? （）
A. RIP routes will be allowed in Area 1 only if they are first redistributed into EIGRP.
B. Because NSSA will discard type 7 LSAs, redistributed RIP routes will not be allowed in Area 1.
C. Redistrib uted RIP routes will be allowed in Area 1 because they will be changed into type 5 LSAs in Area 0 and passed on into Area 1.
D. Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 7 LSAs in Area 0 and passed on into Area 1.
E. Because Area 1 is an NSSA, redistributed RIP routes will not be allowed.
A network administrator is troubleshooting a redistribution of RIP routes into OSPF. Given the exhibited configuration commands, which statement is true? （）
A. Redistributed ro utes will be tagged as external type 1 (E1) with a metric of 30.
B. Redistributed routes will be tagged as external type 2 (E2) with a metric of 20.
C. Redistributed routes will maintain their original RIP routing metric.
D. Redistributed routes will ha ve a default metric of 0 and will be treated as unreachable and not advertised.
E. Redistributed routes will have a default metric of 0 but will not be treated as reachable and will be advertised.
A. 39
B. 39.0100
C. 39.0100.0102
D. 0001
E. 0001.0c00
F. 0001.0c00.1211
A. supports route tags
B. supports more routers in an area
C. does not require Hello packets to establish neighbor relationships
D. produces fewer link state advertisements for a given network
E. supports network layer protocols other than IP
F. requires fewer neighbor relationships in a broadcast multiaccess network
A. forms adjacencies with all neighbors
B. supports demand circuit routing
C. provides routing support for multiple network layer protocols
D. utilizes SPF algorithm
E. provides for network scalability by allowing the network to be separated into areas
F. three layers of hierarchical routing
A. Internet Protocol address
B. Media Access Control address
C. Packet Layer Proto col address
D. Network Service Access Point address
E. Authority and Format Identifier address
A. The cost is set to 10 for all interfaces.
B. The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.
C. The cost is based on the speed of the interface.
D. The cost is based o n a composite of bandwidth and delay of the interface.
A. complete SNP (CSNP)
B. partial SNP (PSNP)
C. hello
D. database query
E. database description packet (DDP)
最新試題
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）