Refer to the exhibit. On the basis of the output generated by the show commands,
which two statements are true?()
A. Because it is configured as a trunk interface, interface gigabitethernet 0/1 does not appear in the show vlan output.
B. VLAN 1 will not be encapsulated with an 802.1q header.
C. There are no native VLANs configured on the trunk.
D. VLAN 2 will not be encapsulated with an 802.1q header.
E. All interfaces on the switch have been configured as access ports.
F. Because it has not been assigned to any VLAN, interface gigabitethernet 0/1 does not appear in the show vlan output.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Based upon the output of show vlan on switch CAT2,
what can we conclude about interfaces Fa0/13 and Fa0/14? ()
A. that interfaces Fa0/13 and Fa0/14 are in VLAN 1
B. that interfaces Fa0/13 and Fa0/14 are down
C. that interfaces Fa0/13 and Fa0/14 are trunk interfaces
D. that interfaces Fa0/13 and Fa0/14have a domain mismatch with another switch
E. that interfaces Fa0/13 and Fa0/14have a duplex mismatch with another switch
Refer to the exhibit. Switch P1S1 is not applying VLAN updates from switch P2S1.
What are three reasons why this is not occurring?()
A. Switch P2S1 is in server mode.
B. Switch P1S1 is in transparent mode.
C. The MD5 digests do not match.
D. The passwords do not match.
E. The VTP domains are different.
F. VTP trap generation is disabled on both switches.
Refer to the show interface Gi0/1 switchport command output shown in the exhibit.
Which two statements are true about this interface?()
A. This interface is a member of a voice VLAN.
B. This interface is configured for access mode.
C. This interface is a dot1q trunk passing all configured VLANs.
D. This interface is a member of VLAN7.
E. This interface is a member of VLAN1.
You’re a network administer and you issue the command (show port 3/1) on an Ethernet port. To your surprise you notice a non-zero entry in the ’Giants’ column.
What could be the cause of this? ()
A. IEEE 802.1Q
B. IEEE 802.10
C. Misconfigured NIC
D. User configuration
E. All of the above
The Company administrator has issue the "show vlan id 5" command.
What will this command display? ()
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group? ()
A. DAI
B. STP
C. PVLAN
D. port security
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings.
Which command sequence would configure interface FastEthernet 0/13 as displayed in Figure 2? ()
A. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode trunk SW1(config-if)# switchport trunk native DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
B. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic auto SW1(config-if)# switchport trunk native DATA SW1(config-if)# witchport trunk allowed vlan add 1,10,20
C. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
D. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan 10 SW1(config-if)# switchport trunk allowed vlan 1,10,20
E. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic Desirable SW1(config-if)# switchport trunk native vlan 10
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch,
which interface command is used to convert a Layer 3 interface to a Layer 2 interface?()
A. switchport access vlan vlan-id
B. switchport
C. switchport mode access
D. no switchport
E. None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 and cannot access network resources. On the basis of the information in the exhibit,
which command sequence would correct the problem?()
A. SW1(config)# vlan 10SW1(config-vlan)# no shut
B. SW1(config)# interface fastethernet 0/1SW1(config-if)# switchport mode accessSW1(config-if)# switchport access vlan 10
C. SW1(config)# interface fastethernet 0/1SW1(config-if)# switchport mode access
D. SW1(config)# vlan 10SW1(config-vlan)# state active
E. SW1(config)# interface fastethernet 0/1SW1(config-if)# no shut
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them.
What will be the result?()
A. IEEE 802.1D and IEEE 802.1w are incompatible. All three switches must use the same standard or no traffic will pass between any of the switches.
B. Switches S1, S2, and S3 will be able to pass traffic between themselves.
C. Switches S1, S2, and S3 will be able to pass traffic between themselves. However, if there is a topology change, Switch S2 will not receive notification of the change.
D. Switches S1 and S3 will be able to exchange traffic but neither will be able to exchange traffic with Switch S2
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Which statement is correct about RSTP port roles?()
What two things will occur when an edge port receives a BPDU?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct, what will be true about Switch 15?()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
Which statement is correct about the use of the virtual interface on a WLC ?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Which two statements are true when the extended system ID feature is enabled? ()