The Frame Relay network in the diagram is not functioning properly.What is the cause of the problem?()
A.The Gallant router has the wrong LMI type configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly
您可能感興趣的試卷
你可能感興趣的試題
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface
B.Configure each Frame Relay circuit as apoint-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
A.A CSU/DSU terminates a digital local loop
B.A modem terminates a digital local loop
C.A CSU/DSU terminates an analog local loop
D.A modem terminates an analog local loop
E.A router is commonly consideredaDTEdevice
F.A router is commonly considereda DCE device
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?()
A.The Seria l0/0interface is passing traffic.
B.The DLCI 100 was dynamic allyallocated by the router
C.The Seria l0/0 interf aceacquired the IP address of 172.16.3.1 from a DHCP server
D.The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud
E.The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
A.can be used over analog circuits
B.maps Layer 2 to Layer 3 address
C.encapsulates several routed protocols
D.supports IP only
E.provides error correction
A.point-to-point
B.broadcast multi-access
C.nonbroadcast multi-access
D.nonbroadcast multipoint.broadcast point-to-multipoint
Refer to the exhibit.Which statement describes DLCI 17?()
A.DLCI 17 describes the ISDN circuit between R2 and R3.
B.DLCI 17 describes a PVC on R2.It cannot be used on R3 or R1.
C.DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D.DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
A.ermit all packet smatching the first three octets of the source address to all destinations
B.permit all packet matching the last octet of the destination address and accept all source addresses
C.permit all packet matching the host bits in the source address to all destinations
D.permit all packet from the third subnet of the network address to all destinations
最新試題
一堆交換機一個server、一個transpare,問配置prune在哪里配置?
aaa架構中哪個是要求用戶輸入用戶名和密碼?
What is the three main step of using the QoS feature with MQC command line interface?
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2.The routers cannot establish an adjacency relationship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.Based on the information in the graphic,what is the cause of this problem?()
what is the disadvantage of policing?
什么是NAT?
QoS機制中的分類,采用ip數據包中的哪個字段?
What is method list for configure aaa?
As a CCNA candidate,you must have a firm understanding of the IPv6 address structure.Refer to IPv6 address,could you tell me how many bits are included in each filed?()
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?()