單項選擇題Which port state is introduced by Rapid-PVST?（）

A.learning
B.listening
C.discarding
D.forwarding


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）

A.HostA is not on the same subnet as its default gateway
B.The address of SwitchA is a subnet address
C.The Fa0/0 interface on RouterA is on a subnet that cannot be used
D.The serial interfaces of the routers are not on the same subnet
E.The Fa0/0 interface on RouterB is using a broadcast address

2.單項選擇題

Refer to the exhibit。A problem with network connectivity has been observed.It is suspected that the cable connected to switch port Fa0/9 on Switch 1 disconnected.What would be an effect of tis cable being disconnected?（）

A.Host B would not be able to access the server in VLAN9 until the cable is reconnected
B.For less than a minute ,Host B would not be able to access the server in VLAN9.Then normal network function would resume.
C.Communication between VLAN3 and the other VLANs would be disabled
D.The transfer of files from Host B to the server in VLAN9 would be significantly slower.

3.多項選擇題

Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? （）

A.Configure the gateway on Host A as 10.1.1.1.
B.Configure the gateway on Host B as 10.1.2.254.
C.Configure the IP address of Host A as 10.1.2.2.
D.Configure the IP address of Host B as 10.1.2.2.
E.Configure the masks on both hosts to be 255.255.255.224.
F.Configure the masks on both hosts to be 255.255.255.240.

4.多項選擇題

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）

A.All of the routers need to be configured for backbone Area 1.
B.R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C.A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D.The hello and dead interval timers are not set to the same values on R1 and R3.
E.EIGRP is also configured on these routers with a lower administrative distance.
F.R1 and R3 are configured in different areas.

6.單項選擇題VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?（）

A.The command is accepted and the respective VLAN is added to vlan dat.
B.The command is rejected.
C.The command is accepted and you must configure the VLAN manually.
D.The port turns amber.

7.單項選擇題In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a switched LAN?（）

A.after broken links are re-established
B.in an improperly implemented redundant topology
C.when upper-layer protocols require high reliability
D.during high traffic periods
E.when a dual ring topology is in use

8.多項選擇題Which router IOS commands can be used to troubleshoot LAN connectivity problems?（）

A.ping
B.tracert
C.ipconfig
D.show ip route
E.winipcfg
F.show interfaces

9.單項選擇題

Refer to the exibit .An attempt to deny web access to a subnet blocks all traffic from the subnet.Which interface command immedicately removes the effect of ACL 102?（）

A.no ip access-group 102 in
B.no ip access-group 102 out
C.no ip access-list 102 in
D.no ip access-class 102 out
E.no ip access-class 102 in

10.單項選擇題What will happen if a private IP address is assigned to a public interface connected to an ISP?（）

A.Addresses in a private range will be not routed on the Internet backbone.
B.Only the ISP router will have the capability to access the public network.
C.The NAT process will be used to translate this address in a valid IP address.
D.Several automated methods will be necessary on the private network.
E.A conflict of IP addresses happens, because other public routers can use the same range.