A.neighbor table
B.SPF table
C.RTP table
D.topology table
E.query table
F.DUAL table
您可能感興趣的試卷
你可能感興趣的試題
A.1024
B.2046
C.4094
D.4096
E.8190
A.assigning a private IP address to the AP
B.changing the default SSID value
C.configuring a new administrator password
D.changing the mixed mode setting to single mode
E.configuring traffic filtering
A.The switch will not forward unicast frames.
B.The switch will forward the frame to a specific port.
C.The switch will return a copy of the frame out the source port.
D.The switch will remove the destination MAC from the switch table.
E.The switch will forward the frame to all ports except the port on which it was received.
A.can be used over analog circuits
B.maps Layer 2 to Layer 3 address
C.encapsulates several routed protocols
D.supports IP only
E.provides error correction
A.default gateway
B.DNS servers
C.FTP server
D.helper address
E.subnet mask
F.TFTP server
A.It sends data in clear text format.
B.It is no longer supported on Cisco network devices.
C.It is more secure than SSH
D.It requires an enterprise license in order to be implemented.
E.It requires that the destination device be configured to support Telnet connections.
A.Switches take less time to process frames than hubs take.
B.Switches do not forward broadcasts.
C.Hubs can filter frames.
D.Using hubs can increase the amount of bandwidth available to hosts.
E.Switches increase the number of collision domains in the network.
A.A successor route is used by EIGRP to forward traffic to a destination.
B.Successor routes are saved in the topology table to be used if the primary route fails.
C.Successor routes are flagged as "active" in the routing table.
D.A successor route may be backed up by a feasible successor route.
E.Successor routes are stored in the neighbor table following the discovery process.
A.Switch1(config-if)# switchport port-security maximum 1
B.Switch1(config)# mac-address-table secure
C.Switch1(config)# access-list 10 permit ip host
D.Switch1(config-if)# switchport port-security violation shutdown
E.Switch1(config-if)# ip access-group 10
A.It divides the network communication process into smaller and simpler components, thus aiding component development, design, and troubleshooting.
B.It enables equipment from different vendors to use the same electronic components, thus saving research and development funds.
C.It supports the evolution of multiple competing standards, and thus provides business opportunities for equipment manufacturers.
D.It encourages industry standardization by defining what functions occur at each layer of the model.
E.It provides a means by which changes in functionality in one layer require changes in other layers.
最新試題
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?()
Three access ports have been installed and configured to a small office.What term defines the wireless topology?()
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()
At which layer of the OSI model is RSTP used to prevent loops?()
Which statement describes the rule of split horizon?()
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?()
What is the purpose of the cisco Vlan Trunking protocol?()
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()