A.Security increases because only the network administrator may change the routing tables.
B.Configuration complexity decreases as network size increases.
C.Routing updates are automatically sent to neighbors.
D.Route summarization iscompued automatically by the router.
E.Routing traffic load is reduced when used in stub network links
F.An efficient algorithm is used to build routing tables,using automatic updates.
G.Routing tables adapt automatically to topology changes.
您可能感興趣的試卷
你可能感興趣的試題
A.RSTP significantly reduces topology reconverging time after a link failure.
B.RSTP expends the STP port roles by adding the alternate and backup roles.
C.RSTP port atates are blocking,discarding,learing,or forwarding.
D.RSTP also uses the STP proprsal-agreement sequence.
E.RSTP use the same timer-baseed process as STP on point-to-point links.
F.RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
A.IronPort
B.Cisco NAC
C.SAN
D.CSA
A.NAT protects network security because private networks are not advertised.
B.NAT accelerates the routing process because no modifications are made on the packets.
C.Dynamic NAT facilitates connections from the outside of the network.
D.NAT facilitates end-to-end communication when IPsec is enable.
E.NAT eliminates the need to re-address all host that require extemal access.
F.NAT conserves addresses through host MAC-level multiplexing.
Refer to the exhibit.Why are two OSPF designated routers designated routers identified on Core-Router?()
A.Core-Router is connected more than one multi-access network
B.The router at 208.149.23.130 is a secondary DR in case the primary fails.
C.Two router IDs have the same OSPF priority and are therefore tied for DR election
D.The DR ecection is still underway and there are two contenders for the role
A.最小特權觀念
B.進程之間的隔離
C.標準檢測器
D.小的、可驗證的代碼塊
A.Cisco網絡準入控制
B.終端保護
C.網絡感染遏制
D.CSA
A.The address is a broadcast address
B.The Ehernet interface is faulty
C.VLSM-capable routing protocols must be enable first on the router.
D.This address is a network address.
A.啟用端口安全
B.跟橋保護
C.廣播風暴控制
D.Cisco安全端口分析器
A.RIPng
B.OSPFv3
C.static
D.IS-IS for IPv6
A.to confine network instability to single areas of the network.
B.to reduce the complexity of router configuration.
C.to speed up convergence.
D.to lower costs by replacing routers with distribution layer switches.
E.to decrease latency by increasing bandwidth.
F.to reduce routing overhead.
最新試題
PC 無法連接到任何遠程網站,無法ping 通其默認網關,也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常?()
在Cisco IOS 設備中,啟動配置文件存儲于何處?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()
要將數據包發送到遠程網絡,應使用哪種設備?()
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么?()
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2?()
以下哪兩種介質可提供高達1Gb/s 的帶寬?()
何時必須使用clock rate 命令配置路由器串行接口?()
請參見圖示。公司路由器由于故障被更換。更換路由器之后,Education 辦公室內的主機C 和D 能夠相互ping 通,但是無法訪問Accounts 辦公室內的主機。此問題的原因可能是什么?()