A、LO OIL INJECTION TEMPERATURE BYPASS
B、FILTER DIFFERENTIAL PRESSURE CHANGE-OVER TIMER
C、PUMP RUN LIMIT WITHOUT OIL PRESSURE TIMER
D、AUTO RESTART AFTER POWER FAILURE TIMER
您可能感興趣的試卷
你可能感興趣的試題
A、MOTOR STARTER AUXILIARY CONTA、CT BYPASS
B、OIL PUMP PRELUBE BEFORE START TIMER
C、OIL PRESSURE BYPASS ALLOW TIMER
D、OIL PRESSURE FAILURE DELAY TIMER
A、MOTOR STARTER AUXILIARY CONTA、CT BYPASS
B、OIL PUMP PRELUBE BEFORE START TIMER
C、OIL PRESSURE BYPASS ALLOW TIMER
D、OIL PRESSURE FAILURE DELAY TIMER
A、CAPACITY INCREASE SOLENOID OFF TIMER
B、CAPACITY DECREASE SOLENOID ON TIMER
C、CAPACITY DECREASE SOLENOID OFF TIMER
D、SLIDE VALVE RETURN AT SHUTDOWN TIMER
A、CAPACITY INCREASE SOLENOID OFF TIMER
B、CAPACITY DECREASE SOLENOID ON TIMER
C、CAPACITY DECREASE SOLENOID OFF TIMER
D、SLIDE VALVE RETURN AT SHUTDOWN TIMER
A、LO RUN OIL PRESSURE
B、HI START FILTER DIFFERENTIAL PRESSURE
C、HI RUN FILTER DIFFERENTIAL PRESSURE
D、CAPACITY INC、REASE SOLENOID ON TIMER
A、LO RUN OIL PRESSURE
B、HI START FILTER DIFFERENTIAL PRESSURE
C、HI RUN FILTER DIFFERENTIAL PRESSURE
D、CAPACITY INC、REASE SOLENOID ON TIMER
A、LO RUN OIL PRESSURE
B、HI START FILTER DIFFERENTIAL PRESSURE
C、HI RUN FILTER DIFFERENTIAL PRESSURE
D、CAPACITY INC、REASE SOLENOID ON TIMER
A、LO OIL INJECTION TEMPERATURE
B、HI OIL INJECTION TEMPERATURE
C、LO SUCTION PRESSURE
D、HI DISCHARGE PRESSURE
A、LO OIL INJECTION TEMPERATURE
B、HI OIL INJECTION TEMPERATURE
C、LO SUCTION PRESSURE
D、HI DISCHARGE PRESSURE
A、LO OIL INJECTION TEMPERATURE
B、HI OIL INJECTION TEMPERATURE
C、LO SUCTION PRESSURE
D、HI DISCHARGE PRESSURE
最新試題
加到系統上的干擾信號（干擾量），由原來數值（）到另一數值上，并繼續保持此值不變，這就是階躍干擾
當電器閥門定位器輸入信號為（）mA時進行安裝更合適
介質中含懸浮顆粒，并且黏度較高，要求泄露量小應選用下列哪種閥門（）
電磁閥通常在管路中起的作用是（）
敷設管纜應留有適當?shù)膫溆眯緮?shù)與長度，固定時應保持其自然繞度，彎曲半徑不得小于管子外徑的（）倍
一般規定管線介質壓力大于（），溫度在－50～600℃為高壓管線
露點分析儀的傳感器包含一個表面鍍（）的惰性（）反射鏡
流量特性在開度較小時就有較大流量，隨著開度的增大，流量很快就達到最大，此后再增加開度，流量變化很小，此特性稱為（）
保護管彎制要使用彎管機冷彎，單根護管的直角彎不得超過（）
作為直接控制用的電磁閥多用在操作不方便處的排污或放空，這時電磁閥直接接在工藝管道上，一般為（）左右